my work

Lofting Take 1

My degree is in Computer Science, which is one of the growing points on the tree of Mathematics. But like everyone else, I suffered through high school Geometry thinking, "Im never going to use this stuff... why are they teaching it?"

And I was right. For 30 years, practicing in a field of Mathematics every day, I never did use that Geometry. It wasnt until I was ready to pound my head in frustration on a concrete wall that I finally figured out why it was still part of the curriculum...

Having mounted my lofting board firmly on my basement wall, I was ready to "lay down" the lines of my boat. I would begin with the Profile view, and the first step was to draw the standard lofting grid of horizontal and vertical lines:


While this grid might look abstract at first glance, the horizontal and vertical grid lines have concrete, physical meaning:

The L.W.L., or Load Waterline, for example, shows where the surface of the water will be, when the boat is floating. The Floor Line shows where my basement floor will be, when the boat is built upside down.

The vertical lines on the lofting grid are called stations. Station A shows where the absolute front of the boat is. If you held a straight edge vertically at station A, the bow of the imaginary boat would just kiss its edge. Likewise, station S shows the absolute back of the boat.

Station 0 shows where the bow of the boat will slip into the water. Station 5 shows where the stern will emerge from the water. And the strong wooden forms, that Cabin Boy will be built on, will be positioned on my basement floor at stations 1, 2, 3, and 4.

In other words, there is nothing abstract about the lofting grid. Any errors I make in the grid will physically distort the shape of my boat. If the lines are not parallel to each other, and the proper distance apart, the boat I build will not be Cabin Boy, but some other boat, designed not by the hand of John Atkin, but by the ugly, misshaping hand of Error.

There are lots of ways to draw a lofting grid. Probably the simplest method is to snap a chalk line near the bottom of the lofting board and call it the Base Line. If you nail a long strip of wood (called a batten in boat-speak) along the Base Line, then you can use a large steel carpenters square to measure off and draw in the vertical lines. Once you have them perfectly vertical, it should be simple to measure up the verticals to draw in the L.W.L. and Floor Line. Easy peasy, and probably pretty accurate.




Nevertheless, too stubborn for my own good, I persisted, and managed to draw both the Profile and Body Plan grids using this technique. When I was done, all the grid lines looked perfect.

It wasnt until I started laying out the lines for the Body Plan that I realized something was wrong. The Body Plan lines, projected onto the Floor Line amplified my errors. All the lines were off by a 1/4" or 1/2". Far to big to ignore. I had done something wrong.

I remeasured all the offsets, but they were correct. The only thing left was the grid. When I measured the distance from the Floor Line to the L.W.L. at one end of the grid, and compared it to the distance at the other end of the grid, I realized that they were not parallel... not even close.

So how could two lines that were perfectly level, as measured (again) by my yellow plastic spirit level, not be parallel? In other words, how could gravity be wrong?

Im sure experienced wood workers smelled the problem as soon as they saw the photo of my spirit level. In a quality, precision spirit level, the ends of the bubble line up exactly with both lines on the glass when leveled. My cheap plastic level had a good 1/8" gap between the bubble and the lines, on both sides.

That left plenty of room for error. A quick calculation told me that even if I was able to measure level to within 1/4th of a degree, that tiny error projected over the 8 ft. length of my lofting grid translates into almost a .5 inch error. Clearly not good enough.


After kicking the basement wall a few times, I realized that it was time to refactor, as we say in the programming world. In English, that means take out the old eraser, and try again.

And thats when I suddenly realized that an old trick from High School Geometry could come in handy...

Next Installment: Lofting - Take 2